Martha Stewart Living 7205008-62 Instruction Manual download pdf

Fig 2

ASSEMBLY OF THE TREE STAND

1. Remove the tree stand parts from its protective wrapping

in box 1.

2. To attach the support legs to the tree stand, lay the stand

on its side. Place a hex bolt in 2 of the pre-drilled holes in

the stand. Place a leveling washer on the OUTSIDE hex

bolt.

3. Align a support leg, with its pre-drilled holes, over the 2

protruding hex bolts. (The flat surface of the support leg

should be flush against the bottom of the center hub).

4. Thread the hex nuts onto the hex bolts and tighten.

Repeat steps 2 - 4 for the remaining 3 support legs (Fig 2).

5. Place the tree stand in its desired location; as once the

tree is fully assembled, it will be too difficult to move and

relocate.

11. Carefully cut the nylon strapping bounding the branches

upright; being careful not to cut any exposed light set wires;

and gently guide the branches downward into place.

12. As described previously; you will now continue to build your

tree upward, by attaching section “C” onto section “B”.

10. Align the flat ends of both connectors as shown and

connect them together. Slide the screw cover from the

“male” connector over the “female” connector and

tighten (Fig 5).

1. Locate the bottom section of the tree which is identified

by a label on the outer branches marked “A.”

2. Remove the protective plastic cap from the end of the

pole and place that end into the tree stand. Be sure the

end of the pole reaches the bottom of the stand.

3. Now tighten all 6 hex bolts firmly and securely on the tree

stand center hub; being careful not to over-tighten. (Fig 3).

Fig 1

Carefully unpack all tree components from the 3

cartons (Fig 1). Your tree should include the following:

1 metal tree stand, (center hub), with 6 attached hex

bolts

4 metal tree stand support legs

1 Bag of long hex bolts, leveling washers and hex nuts

A dual function control-switch with extension cord and

plug; attached to both tree sections “A” and “D”

1 Bag of replacement bulbs included with these

instructions

Tree sections as noted below:

12’ tree – 7 sections

PRE-ASSEMBLY

Packaging Contents

Model No. 7205008-62

Fig 3

4. Carefully cut the nylon strapping bounding the branches

upright; being careful not to cut any exposed light set wires;

and gently guide the branches downward into place.

5. Under the tree’s canopy of section “A”, contains a dual

function control switch, attached to an extension cord with

plug. Remove the twist-tie bounding the extension cord

and insert the plug into a working electrical outlet or

electrical plug strip. (Fig 7).

6. “Click” the dual function control switch, selecting from off,

warm white and multi-color LED light positions.

PLEASE NOTE: This dual function control switch will be

operating sections “A”, “B” and “C” only. A 2nd dual function

control switch, (located in section “D”), will be operating

sections “D”, “E”, “F” and “G”. See (Fig 6).

7. Locate the next section of the tree which is identified by a

label on the outer branches mark “B”. (Fig 6).

8. Removing the protective plastic cap from the end of the

pole on section “B”; insert that end onto the top of the

exposed pole of section “A” until it is fully seated.

9. To electrically connect the sections, locate the coaxial

connectors labeled “1.” There will be one connector in

section “A” and one in section “B” of your tree (Fig 4).

Note: Do not remove the connector labels, as they will help

you disassemble and reassemble the tree in the future.

Fig 4

Fig 5

1. If the tree or a section fails to illuminate; one of the two dual function

control-switches; may be in the center “off” position. “Click” the dual

function control switches accordingly.

2. If the tree or a section fails to illuminate; check all of the coaxial

connections as shown in Fig 4, Fig 5 and Fig 6).

3. NOTE: Always check your tree for any loose, unlit or damaged bulbs.

Although the tree will still continue to light; the bulbs must be

replaced promptly to ensure the performance and life expectancy of

your tree.

TROUBLESHOOTING

NOTE: DO NOT USE A DIMMER SWITCH OR INSTALL ANY

ADDITIONAL CHRISTMAS LIGHTING OR ORNAMENTATION THAT IS

DAMAGE TO YOUR CHRISTMAS TREE OR CAUSE PERSONAL INJURY.

THIS ACTION WILL RESULT IN A VOID OF THE LIMITED WARRANTY OF

THIS PRODUCT.

NOTE: Though the light strings are rated for indoor or

outdoor use, the complete tree is for indoor use only.

13. As indicated in step #6; there is a 2nd dual function control

switch with an extension cord and separate plug, attached to

the under-canopy of tree section “D”. Upon placing section “D”

atop of section “C”; remove the twist-tie bounding the

extension cord, and begin to thread this additional cord and

plug downward throughout the tree as close to the center pole

as possible until reaching floor level. Insert the plug into a

working electrical outlet or electrical plug strip. (Fig 7).

NOTE: There are no electrical coaxial connections, connecting

section “C” to section “D”.

14. Carefully cut the nylon strapping bounding the branches

upright; being careful not to cut any exposed light set wires;

and gently guide the branches downward into place.

15. You will now have to “Click” the dual function control switch

from section “D”; to a selection that matches that of your

selection from the dual function control switch from section “A”.

(off, warm white or multi-color). See (Fig 7).

16. As described previously; you will continue to build your tree

upward, attaching section “E” onto section “D”, “F” onto section

“E” and “G” onto section “F”. See (Fig 4, Fig 5 and Fig 6).

17. Always check your tree for any loose, unlit or damaged bulbs.

Although the tree will still operate, the bulbs must be replaced

promptly to ensure the performance and life expectancy of

your tree.

Connection 2

Connection 3

Connection 4

Connection 5

Connection 1

Dual

function

control

switch

Fig 6

Extension

cord

1. Gently remove the plugs from their electrical outlet, and carefully

bound the extension cord containing the dual function control

switch and plug from section “A”.

2. Beginning with the tree’s top section working downward; lift off

each section slowly upward; and locating the coaxial connections,

unscrew the “male” cover cap in a counter-clockwise motion and

gently pull apart the male/female coaxial connection.

3. NOTE: When removing section “D”; lift section “D” upward and grasp

the extension cord containing the dual function control switch and

plug. Slowly raise the extension cord through the branches of

sections “A”, “B” and “C” until freed. Carefully bound the extension

cord containing the dual function control switch and plug from

section “D”.

4. As you lift and remove each section from the section below; gently

fold the branches of each section upward, towards the center, and

position in a storage container. NOTE: With the exception of the

tree’s “Top” section; by holding each section upside down; the

branches will collapse downward, due to the hinging, aiding in the

packing of each section into the storage container.

5. To remove the bottom section from the tree stand; loosen all 6 hex

bolts from the tree stand’s center hub and lift the bottom section out

of its stand.

6. To disassemble the tree’s stand; Reverse the order from the

“Assembly of the Tree Stand” section. NOTE: It is recommended to

leave the stand assembled; if storage room permits.

7. It is recommended to always store the tree in a cool, dry location

protected from excessive exposure to heat or sunlight.

DISASSEMBLY & STORAGE OF THE TREE

ASSEMBLY OF THE TREE

CAUTION: An adequate sized ladder is recommended in the

assembly of this tree. A person to assist in the assembly and

support of said ladder is also highly recommended.

Tipping of the tree, in order to assemble, as each lettered

section is added; can result in damage due to the stress

caused to the tree’s center pole.

Made in China

Printed in China

This is not a toy, for decorative use only.

WARRANTY INFORMATION

If for any reason, after assembly, the tree does not light please call

our toll free number 1-877-527-0313.

The limited warranty of this tree applies only to the original

purchaser against manufacturer defects. A valid sales receipt must

be retained as proof of purchase. This product was pre-tested before

shipment and date coded.

The warranty of this pre-lit tree is void when the product is used for

commercial purposes.

Warranty on Lights:

For up to 5 years from the date of purchase, Home Depot will replace

free of charge any manufacturer defect found to the lighted portion

of your tree.

Warranty on Tree:

For up to 5 years from the date of purchase, Home Depot will replace

free of charge any manufacturer defect found to the tree.

Note: After your pre-lit tree is assembled, please check your tree for

any loose or damaged bulbs. Loose or damaged bulbs must be

replaced promptly in order to maintain the performance and life

expectancy of your pre-lit tree. If a bulb burns out, please replace it

at once (see replacement instructions). Failure to replace a burned

out bulb will result in a shorter life span for the remaining bulbs.

Failure to replace burned out bulbs, or misuse of this product will

void the warranty. This Christmas tree is a seasonal product. It is

intended for indoor use only and for temporary (90 days max)

installation and use only. Keep away from heat and moisture.

DISTRIBUTED BY HOME DEPOT U.S.A., INC. 2455

CCT13

Fig 7

15”

2013 MSL

12 ft Tree Instruction Sheet - Color Changing - Dual Function (English)

Date: 6/3/13

7205008-62 (12 ft Regal Fir)

11.5”

1 2

Summary of Contents

Page 1 - Printed in China

Fig 2ASSEMBLY OF THE TREE STAND1. Remove the tree stand parts from its protective wrapping in box 1.2. To attach the support legs to the tree stand, l

Page 2 - Impreso en China

Fig 211. Corte cuidadosamente la cinta de nilón que mantiene las ramas juntas y derechas; cuidado de no cortar cualquier cable de los ensambles de luc

Comments to this Manuals

No comments

Martha Stewart Living 7205008-62 Instruction Manual

Browse online or download Instruction Manual for Unknown Martha Stewart Living 7205008-62. Martha Stewart Living 7205008-62 Instructions / Assembly User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Unknown Martha Stewart Living 7205008-62